Home Monitoring System – Version 1.0

Having worked on my home monitoring system on an off for the last number of weeks I have finally gotten to version 1 for the host board and the sensor nodes.

Temperature And Humidity Sensor Node

I completed the development and testing of the wireless temperature and humidity sensor nodes.

This board was installed in an enclosure as shown below. The board was designed to fit snuggly into the enclosure which takes two AAA batteries to power the sensor.

The sensor implements a simple channel scanning and handshake protocol which allows it to determine the radio frequency channel the wireless hub is listening for packets. When the channel is found by sending a NodeHello packet to which the wireless hub replies with a NodeHelloAck packet. The NodeHelloAck packet contains configuration data that the node uses to setup it logical RF channel.

Once the handshake has completed the node enters a loop where it sleeps for a period, which is provided as part of the handshake data, wakes up and transmits the latest temperature, humidity and battery voltage readings to the wireless base station.

Wireless Hub

I chose a Netduino Plus 2 as the hardware for the wireless hub. The hardware setup is pretty straight forward. An NRF24L01P radio module is connected to power and the SPI port on the Netduino.

The Netduino implements a simple web server, based on embeddedwebserver, that hosts a set of pages that renders the sensor data from each of the sensors, allows configuration changes to be made and log file viewing. Since the Netduino has limited memory and CPU most of the processing for data rending is offloaded onto the browser. The sensor data page uses a JavaScript graphing component called Rickshaw. The pages are rendered on the client side browser as a single page application using AngularJs as the MVVM framework and Bootstrap to provide a responsive UI that scales to different device screen sizes.

Sensor Data Display

The sensor data is rendered on the main page of the application. The interface allows selection of a number of days of data. Multiple sensor feeds can be rendered, the graphing component supports hoover details when the mouse is over a point on the graph.

Nodes Configuration

The nodes configuration page shows active nodes and the node types. The nodes name can be modified.

System Log

The logging level is set on the configuration page from 0 to 4, 0 = None 4 = Debug

Configuration

The configuration page allows the following to be configured:

• The radio channel
• The radio device address
• The log level
  • None
  • Info
  • Warn
  • Error
  • Debug
• Update interval, the rate that the sensor will push readings

Future Additions

• Minor web UI clean up and changes
• The ability to export sensor data
• The ability to have a node release its allocated id

I would also like to add some additional sensor types, maybe air quality, water,power etc. Later I would like to use the data gathered to directly control the space heating from the netduino, via a relay node that can be used to advance and retard the heating system based on evaluation of the temperature data. For example on a very cold day fire up the heat at an earlier time than the heating control system would normally.

Home Monitoring System – Sensor Node

Finally the boards that I designed for the home monitoring system arrived from OSH Park. Son now I can get down to building the the boards. The photo below shows the board in the bottom half of the enclosure that I am planning to use.

To ensure that I don't release the blue smoke I decided to build and test the node in a number of steps. For the first step I soldered the components of the power supply and tested the output voltage.

This first step was successful connecting a bench power supply set to 2.8 volts yielded an output of 3.3 volts.

The next step was to solder the remaining capacitors and ICs and resistors. When designing the board I used 0603 for the resistor and capacitor footprints. This was a mistake because they are difficult to hand solder due to the size. Next time I will use the next size up.

The other SMD that was difficult to solder was the LCC8 humidity sensor. In fact I initially soldered it on upside down and had to remove it, in the process of which I destroyed the part. Below is an image of the final board with the debug and ISP header but without the radio module this will be added later.

When I initially attached the ISP I found that it would not connect to the board. The reason for this was that the ISP clock was set to the default of 1Mhz. The ATmega48PA is shipped with internal RC oscillator at 8.0MHz and with the fuse CKDIV8 programmed, resulting in 1.0MHz system clock. Reducing the ISP clock to 1/4 of the CPU frequency resolved the issue.

When I resolved the connection issue to the device I was able to flash the firmware and start testing the sensor board. The first check was to determine if the ADC voltage monitoring circuit worked. This is where I ran into another problem. I powered the board with a bench power supply @ 2.8 volts. Reading the battery voltage via the ADC resulted in a value of 2.1 volts. After examining the battery sensing circuit it initially looked like the p channel FET was not switching on fully causing a voltage drop of 0.6 volts across the Source to Gate. Checking the Drain voltage measured 2.1 volts which was wrong because it was not switched on, i.e. 0 volts applied.

On a hunch I checked the datasheet of the FET against the footprint on the board. I discovered the PMBFJ177 footprint is different the Gate and Drain are interchanged. I will need to get another J177 FET that matches the board footprint.

Once these issues where resolved I was able to debug the code that reads the humidity and temperature from the CC2D33S sensor using the AVR dragon.

The next step is to add the radio module and figure out a strategy to debug and test the radio module and its code.